![]() Work offers a selection of classic Japanese designs for Miatas. The deep dish and beautiful spokes create an understated and refined look. These are legendary Japanese racing wheels. Like Wheels / HalfPast3hree RS Watanabe Miata Wheels I really love the look of these wheels that are designed specifically for the Miata. I first saw these on HalfPast3hree’s incredible Miata. Here is a setup from the Enkei blog: Like Wheels (personal favorite) The RPF1 is a classic wheel in the import world and they look stunning on the Miata. For more options on fender flares / widebody, check out this post. I don’t think I can go much wider without some sort of cutting / modification. I was able to fit 225 wide tires on my miata without adding fender flares. I can’t wait to get them out on the track. The Falken tires are far more aggressive than the previous Continentals. These have so far fit, without significant additional fender rolling.įor tires, I went with 225/45-15 Falken Azenis RT660 SL’s. This would allow me to go significantly wider with the tire and really maximize the chassis. To replace my wheel setup, I stayed with the same wheel model, but went to 15×9 with a +35 offset. Will 15×9 fit on NA Miata with stock fenders? These wheels, with 205/50-15 Continental Extremecontact Sport SL tires, did require some rolling of my fenders ( I used this Eastwood tool). I went for the Matte Bronze color and couldn’t have been happier. ![]() My first set of wheels were the Konig Hexaforms in 15×8 with a +25 offset. They can look dang cool though! Konig Miata Wheels Outside of fringe cases, these are not going to be used on most Miatas that are performance minded. There are fewer tires available in the 16″ sizes, making track day rubber harder to find. 16″ Miata Wheelsġ6’s are great for aesthetic reasons, but will be slightly heavier and more expensive than the typical 15″ wheel. Anything over 9″ wide will likely require fender flares and/or other clearance modifications. You can typically find these in a range of widths from 7″ to 11″. Most aftermarket 15″ wheels are designed to clear big brakes and you will have the largest selection of tires. These will be the best overall size wheel for autocross / track days and racing in general. Good-Win Racing has excellent size recommendations. The offset will depend on the wheel width. The NA and NB Miatas are all 4×100 bolt pattern wheels. If you need more in depth dimensions in regards to how your tire will sit and end up being like, this is not the right tool for you.1995 M 15×6″ – 12 lbs Best Wheels for your Miata Which Size should you go for? DEFINITELY NOT THE PROPER RIDE HEIGHT UNLESS YOU HAVE A BRICK UNDER EACH WHEEL!!!!BUT STRONGLY DOUBT IT. (I measured from ground the center hub wheel when sitting normally then lowered floor jack with another jack under A-arm until at precisely same height to center hub without wheel then check with this tool) DO NOT JUST PUT A BRICK UNDER IT. It is very accurate but can be within (+/-) 1-3mm depending on your prints but can still be close enough! ![]() There are methods to put proper weight on the A-arm/hub when you are checking to make sure car is well/evenly seated. I also used my DeWalt laser to get more of a precise line up to my inner fender. This offset tool is purposely designed to give us an idea of the maximum offset without sticking past your fenders. I printed this with my MSLA ELEGOO SATURN S out off ABS LIKE RESIN mix so: 40% Siraya Tenacious for a bit of flexibility and 60% Siraya Fast for the strength with no support Also printed it with my CREALITY ENDER 3 PRO w/o support at 20% infill and also turn out great. Therefore i came up with my own and offering it to you as a buyable file. Those I saw are not printable via their files but mainly to be purchased online which I totally understand. This wheel offset tool was designed and patented by me based on others that I seen on the internet.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |